ZigStar Stick v4¶
Features¶
- TI CC2652P SimpleLink™ 2.4 GHz Multiprotocol Wireless MCU targeting Zigbee,Bluetooth 5.1 Low Energy,Thread + 19.5-dBm high-power amplifier
- Support RF-BM-2652P1 and RF-BM-2652P2 Module from RF-STAR,with CC2652P on board
- BSL,RST Buttons
- 2 LED for indication
- Compatible with Z2Mand ZHA
- SMA antenna port for an external antenna
- Easy programming with ZigStar Multi Tool.No external programmer needed!
- Communicates via the common CH340E/CH340C USB-UART Bridge
- Plug & Play, comes pre-flashed
Purchase¶
Assembled versions of Zigbee Stick v4 is available for purchase.
Shiping is done from Germany
Each order contains a fully assembled and tested PCBA along with a plastic enclosure and a small +3dBi antenna.
Revisions¶
There are 2 versions of stick,both of them tested:
- CH340C 3D Printed Case version, more easy to solder,Auto-BSL enabled and includes ESD protection.1
- CH340C Factory Case version,2 fits in this factory cases VG-S48/AK-N-12
CH340C versions use this 3D Model Case
Factory cases are found on Aliexpress: VG-S48/AK-N-12
Bill of Materials:¶
EasyEDA Generated Boom,you can order on LCSCdirectly - BOM
| Designator | Name | Footprint | Quantity |
|---|---|---|---|
| U1 | RF-BM-2652P1/P2 | 1 | |
| U2 | AMS1117-3.3 | SOT-223 | 1 |
| U3 | CH340E/CH340C | MSOP-10/SOP-16 | 1 |
| R1 | 10 kohm | SMD 0805 | 1 |
| R2,R3 | 1 kohm | SMD 0805 | 2 |
| R4 | 100 ohm | SMD 0805 | 1 |
| C1 | 10uF | SMD_L3.2-W1.6 | 1 |
| C2,C4 | 100nF | SMD 0805 | 2 |
| C3 | 22uF | SMD_L3.2-W1.6 | 1 |
| L1,L2 | RED/GREEN LED | SMD 0805 | 2 |
| SBL,RST | PUSH BUTTON | SMD_L3.9-W3.0-P4.45 | 2 |
| USB | USB A MALE | USB-A-SMD_USB-A-1-TH | 1 |
| JTAG | PIN HEADER 5 PIN | 2.54x5P | 1 |
| ANT | SMA ANTENNA PORT 1.6mm | 1 | |
| D1 | ESD USBLC6-2SC6 | SOT-23-6 | 1 |
WARNING D1 is used only for CH340C and Factory Case sticks.
Next items are not available on LCSC,you can get them on Aliexpress:
- RF-BM-2652P1/P2
- RP-SMA Antenna PCB Connector 1.2/1.6mm
- RP-SMA Antenna Female - Inner hole
- Cases VG-S48/AK-N-12
Firmware¶
Module is compatible with Z2M. Firmware CC1352P2_CC2652P_launchpad_*.zip.
Default TX Power is 9dbm. It can be adjusted in Z2M config section:
experimental:
transmit_power: 10
Available TX power values: -20,-18,-15,-12,-10,-9,-6,-5,-3,0,1..5,14..20 3
Downloads¶
Video¶
*English subtitles available